• 2026 bundle: free window or gutter cleaning
Interlocking paver patio with clean joints

Paver Patio Cleaning, Polymeric Sand and Sealing: What Ohio Homeowners Should Know

Quick answer: clean pavers with a surface cleaner or low-to-moderate pressure, then refill the joints with polymeric sand once the surface is fully dry. Sealing is optional. It can enhance color and slow staining, but it must be done on clean, dry pavers, and the wrong product can leave a hazy or slick finish.

Pavers are popular around Cleveland for patios, walkways and driveways. They are tough, but they need maintenance. Weeds, moss, ants and loose pavers usually trace back to the joint sand, which is why cleaning pavers is not just about the surface.

Why pavers get dirty

Pavers have joints and a slightly textured surface. That gives algae, weeds and dirt plenty of places to take hold. Shade, trapped moisture and fallen leaves make it worse. Over the years, sand washes out of the joints from rain, pressure washing and foot traffic.

What freeze and thaw does to pavers

Water that gets into joints and the base freezes in winter and expands. This can heave pavers, open gaps and loosen the sand. Poor drainage and a weak base make it worse. After a cold winter you may see:

  • Uneven or rocking pavers
  • Sunken spots
  • Open or empty joints
  • Weeds growing between pavers

Cleaning pavers step by step

  1. Sweep and remove weeds. Pull weeds by the roots and sweep away loose debris.
  2. Pre-wet the surface. This keeps cleaner from soaking in too fast.
  3. Apply a paver-safe cleaner. It should treat algae, mildew and organic stains.
  4. Agitate and rinse. Use a surface cleaner or a wide fan tip at controlled pressure. Keep a steady distance.
  5. Let the pavers dry completely. Sand and sealer need a dry surface and dry joints.

High pressure at close range is the fastest way to blast the sand out of your joints and etch the surface, so go gentle.

Replacing polymeric sand

Polymeric sand is a fine sand with binders that harden when wet. It locks pavers together, limits weeds and discourages insects. After cleaning:

  1. Make sure the joints are clean and at least a bit empty. Old, weak sand can be vacuumed or picked out to a usable depth.
  2. Sweep the new sand into the joints. Fill them fully.
  3. Compact the pavers if needed and sweep again.
  4. Blow or sweep excess sand off the surface, since leftover residue can stain.
  5. Activate it with a light mist following the manufacturer’s directions and weather window.

Rain too soon after installation can wash the binder out and leave a haze, so check the forecast.

Should you seal pavers?

ProsCons
Can enhance colorCan look glossy or hazy if the wrong product is used
Helps stop stainsNeeds reapplying over time
Locks sand and slows weedsCan be slippery if it is a high-gloss film
Easier future cleaningMust be applied to clean, dry pavers

Pick a sealer designed for pavers and your exact material. Test a small area first. Do not seal over damp pavers or sand that has not cured.

How often?

  • Cleaning: at least once a year, more in shade
  • Joint sand check: each spring after winter
  • Resealing: depends on the product and traffic, often every few years

Common mistakes

  • Using a zero-degree or narrow tip that cuts into pavers
  • Cleaning without replacing lost joint sand
  • Sealing before the pavers are dry
  • Ignoring sunken or loose pavers, which get worse over time

Let a pro handle the cleaning

Professional cleaning evens out the color and removes tough stains without gouging the surface. Our concrete and paver cleaning starts at $0.23 per square foot. We clean the pavers so you or your hardscape contractor can resand and seal them afterward. For patios, see our patio cleaning guide.

Frequently Asked Questions

Can you pressure wash pavers?

Yes, with the right tip and pressure. A surface cleaner is the safest way to get an even clean without gouging.

Do I need to re-sand pavers after cleaning?

Often yes. Cleaning and weather loosen the joint sand, and refilling the joints keeps pavers stable and discourages weeds.

How long should pavers dry before sealing?

Follow the sealer instructions, but many require at least a day or two of dry weather so the pavers and joints are completely dry.

Why is white powder coming up on my pavers?

It is usually efflorescence, a salt residue left when moisture moves through the material. It can be cleaned, and sealing can help prevent it.

Does sealing stop weeds?

It helps when combined with fresh polymeric sand, but it does not stop weeds entirely if debris builds up in joints.

Get a Free Quote from ALWAYS B.I.G.

Ready to put this to work? Use the instant estimate on our site, book online in a few clicks, or call or text (216) 202-8264. We serve homeowners and businesses across Cleveland and Northeast Ohio.


About the Author

Michael Betts is the founder of ALWAYS B.I.G. Power Washing Pros, an owner-operated exterior cleaning company serving homeowners and businesses across Cleveland and Northeast Ohio with house washing, roof cleaning, gutter services, window cleaning and concrete cleaning.

Call or text (216) 202-8264, email michael@ohiopowerwashingpros.com, or read more homeowner guides in the Curb Appeal Report.

Call Book NowQuote