Quick answer: clean the driveway thoroughly, treat oil and rust stains, repair cracks and let the concrete dry completely before applying any sealer. Dirt, algae, efflorescence and moisture under the sealer cause peeling, cloudiness and poor adhesion. In Northeast Ohio, plan around a dry stretch with mild temperatures.
Sealing can protect concrete from water, salt and stains, but the sealer is only as good as the surface under it. Most failed sealer jobs start with poor prep. Here is the process that gives sealer its best chance.
Do you need to seal your driveway?
Not always. Sealing can help when:
- The concrete is in good condition and you want extra protection against salt and stains
- It is exposed to road salt, oil and heavy traffic
- You want a deeper color or a specific finish
Concrete that is cracked, flaking or damaged may need repair first. Sealer is not a repair product.
Step 1: inspect the concrete
Look for:
- Cracks wider than a hairline
- Scaling or flaking surface
- Sunken or uneven slabs
- Old sealer that is peeling
Existing sealer usually needs to be removed or tested for compatibility before applying a new one.
Step 2: clean thoroughly
Cleaning removes the dirt and biological growth the sealer would otherwise trap. A proper process:
- Sweep and remove debris.
- Pre-treat stains. Oil needs a degreaser, rust needs a rust remover, and algae needs a biological cleaner.
- Use a surface cleaner. It gives an even result with no wand marks.
- Rinse well. Leftover cleaner can interfere with the sealer.
High pressure alone can etch concrete and leave tiger-stripe lines that show through sealer. Use proper technique and equipment.
Step 3: treat stains
Stains that are not removed will often show through, and sealing locks them in. See how to remove oil stains from a concrete driveway and road salt and winter stains.
Step 4: repair cracks and joints
Fill cracks and control joints with a flexible concrete crack filler or sealant designed for the job. Water getting under the slab is one of the biggest causes of frost damage. If you see widespread cracking or settling, talk to a concrete contractor.
Step 5: let it dry completely
Concrete holds water. Sealing damp concrete can trap moisture and turn the sealer white or cloudy. Most manufacturers want 24 to 48 hours of dry weather and a dry surface. Check the instructions on the product you are using.
Step 6: choose the right sealer
| Type | Good for | Notes |
|---|---|---|
| Penetrating (silane or siloxane) | Salt protection, natural look | Soaks in, no surface film |
| Acrylic film-forming | Color enhancement, glossy or satin | Can wear or peel, needs recoating |
| Epoxy or polyurethane | High-wear surfaces | More demanding to apply |
In Northeast Ohio, many homeowners choose penetrating sealers for driveways exposed to salt, since they do not leave a slick surface film.
Step 7: apply in the right conditions
- Mild temperatures within the product’s range
- No rain in the forecast during the cure time
- Even, thin coats, not puddles
- Keep cars and foot traffic off until the cure time is up
Timing in Ohio
Late spring through early fall often offers the best windows. Cold, damp weather and late-season frosts can stop sealing from curing properly. If you are cleaning in the fall, finish early enough that the concrete can fully dry.
Let us handle the cleaning
We clean driveways and walkways starting at $0.23 per square foot. A 600 square foot driveway starts around $138 plus the 5% transaction fee. Deep oil stains are quoted after we see the surface. After cleaning, you or your sealing contractor can apply the sealer on a clean, dry surface. See our concrete cleaning page.
Frequently Asked Questions
How long after pressure washing can I seal concrete?
Wait until the concrete is fully dry, often 24 to 48 hours in good weather, and follow the sealer’s instructions.
Can I seal a driveway with cracks?
Fill and repair cracks first. Sealer does not bridge or fix structural cracks.
Will sealing stop oil stains?
It can slow absorption, so spills are easier to clean, but it does not make concrete stain-proof.
How often should I reseal a driveway?
It depends on the product and wear, commonly every 2 to 5 years. Watch for water no longer beading on the surface.
Is sealing worth it in Ohio?
Often yes, especially with road salt exposure and freeze and thaw cycles. Penetrating sealers are a popular choice for that reason.
Related reading
- How to Remove Oil Stains From a Concrete Driveway: What Works and What Does Not
- Concrete Spalling and Freeze-Thaw Damage in Cleveland: Causes, Warning Signs and Prevention
- Road Salt, Rust and Winter Stains: Restoring Your Concrete Driveway in Cleveland
Get a Free Quote from ALWAYS B.I.G.
Ready to put this to work? Use the instant estimate on our site, book online in a few clicks, or call or text (216) 202-8264. We serve homeowners and businesses across Cleveland and Northeast Ohio.
About the Author
Michael Betts is the founder of ALWAYS B.I.G. Power Washing Pros, an owner-operated exterior cleaning company serving homeowners and businesses across Cleveland and Northeast Ohio with house washing, roof cleaning, gutter services, window cleaning and concrete cleaning.
Call or text (216) 202-8264, email michael@ohiopowerwashingpros.com, or read more homeowner guides in the Curb Appeal Report.

